الانتقال إلى معلومات المنتج
1 من 3

Schneider Electric BMXFTA152 Modicon X80 Preformed Cord Set

18 في المخزون
  • Manufacturer: Schneider
  • Product No.: BMXFTA152
  • Country of origin: France
  • Product Type: Modicon X80 Preformed Cord Set
  • Condition: جديد تمامًا
  • Payment: تحويل بنكي/ويسترن يونيون
  • Weight: 0.32 kg
  • Shipping port: شيامن
  • Warranty: 12 شهرًا
  • الوصف
  • Reviews
  • الشحن والدفع

Configured for point-to-point analog signal routing in Modicon X80 and Modicon M340 I/O architectures, the Schneider Electric BMXFTA152 (BMXFTA152 Preformed Cord Set) provides direct physical and electrical execution between a 20-pin removable terminal block and a 25-pin SUB-D connector. This 1.5 m cable assembly links the BMXAMO0802 8-channel analog output module directly to the ABE7CPA02 Advantys Telefast sub-base without manual wire-by-wire termination.

Suffix Breakdown & Model Matrix

The BMXFTA152 designation follows the Schneider Electric Modicon X80 cabling nomenclature:

  • BMX: Modicon X80 I/O platform hardware prefix.
  • FTA: Preformed cord set series designed for Modicon X80 to Advantys Telefast ABE7 connection.
  • 15: Cable length indicator specifying a 1.5 m assembly.
  • 2: Connector configuration code denoting a 20-pin removable terminal block (module side) to a 25-pin SUB-D connector (sub-base side).

Hardware Specifications

Parameter Specification
Model BMXFTA152
Brand Schneider Electric
Origin Not specified in source documentation
Weight 0.32 kg
Dimensions 1.5 m length (packaged: 4.0 cm H x 21.0 cm W x 21.0 cm L)
Operating Temp Not specified in source documentation
Power Consumption 0 W (passive interconnect assembly)
Series Modicon X80
Module Side Connector 1 x 20-pin removable terminal block
Sub-Base Side Connector 1 x 25-pin SUB-D male connector
Compatible I/O Module BMXAMO0802 (Modicon M340 / X80 Analog Output)
Compatible Sub-Base ABE7CPA02 (Advantys Telefast)
EAN Code 3595864080468

I/O Density Scaling & Backplane Bus Integration

In high-density Modicon X80 racks, direct field wiring to 20-pin module headers creates mechanical strain and increases termination errors during commissioning. The BMXFTA152 offloads field wiring from the chassis front plane to a DIN-rail mounted ABE7CPA02 Telefast sub-base. By consolidating 8 analog output channels into a single shielded multi-conductor trunk, the assembly preserves backplane bus slot density while isolating field terminal torque stresses from the BMXAMO0802 module printed circuit board.

Frequently Asked Questions

Q: Can the BMXFTA152 be disconnected from the BMXAMO0802 module while the Modicon X80 rack is powered?A: While the Modicon X80 architecture supports module hot-swapping under specific controller configurations, unplugging the 20-pin removable terminal block under load interrupts all active 4-20 mA or 0-10 VDC analog output loops simultaneously, forcing connected actuators to their zero-energy state.

Q: Does this cable draw current from the Modicon X80 backplane bus?A: No. The BMXFTA152 is a strictly passive copper interconnect. All backplane current draw originates solely from the host BMXAMO0802 analog output module.

Q: Is the BMXFTA152 pin-compatible with 28-pin or 40-pin Modicon X80 digital I/O modules?A: No. The module-side connector is mechanically keyed and wired exclusively for 20-pin terminal block headers, specifically matched to the channel pinout of the BMXAMO0802 and ABE7CPA02 combination.

Field Installation Guidelines

  1. Power Isolation: De-energize external 24 VDC loop power supplies feeding the ABE7CPA02 sub-base before mating connectors.
  2. Module-Side Seating: Align the 20-pin removable terminal block with the front header of the BMXAMO0802 module. Press firmly until the top and bottom locking latches engage, then tighten the captive retention screws.
  3. Sub-Base Connection: Mate the 25-pin SUB-D connector to the corresponding port on the ABE7CPA02 Telefast sub-base and secure both thumbscrews to prevent vibration-induced loosening.
  4. Cable Routing & Bend Radius: Route the 1.5 m cable through dedicated analog signal ducts, maintaining at least 200 mm separation from AC power lines and variable frequency drive (VFD) motor leads to prevent electromagnetic interference. Avoid sharp bends within 50 mm of either connector strain relief.

الدفع: تحويل مصرفي (T/T)، ويسترن يونيون.

ميناء الشحن: شيامن.

مدة التجهيز: عادةً من يوم إلى 3 أيام عمل بعد تأكيد الدفع (وفقًا لتوافر المخزون).

التوصيل worldwide: نشحن قطع الأتمتة الصناعية إلى العملاء حول العالم. تُدرج تكلفة الشحن ضمن عرض السعر الخاص بطلب عرض الأسعار (RFQ).

الأسئلة الشائعة

الأسئلة الشائعة حول عروض الأسعار والشحن والضمان والإرجاع

انقر على طلب عرض سعر في صفحة المنتج وأرسل إلينا رقم القطعة والكمية المطلوبة وبلد الوجهة. سيرد فريق المبيعات لدينا بتوفر المنتج حاليًا وسعره ووقت التسليم التقديري.

تُجهَّز المنتجات المتوفرة عادةً بعد الدفع وتأكيد الطلب. تُشحن معظم الطلبات من مستودعنا في الصين، مع أن موقع الشحن قد يختلف حسب المخزون الحالي.

نعم. نشحن قطع الأتمتة الصناعية إلى العملاء في جميع أنحاء العالم. تعتمد تكلفة الشحن ومدة النقل على الوجهة ووزن الطرد وحجم المنتج ومتطلبات الاستيراد المحلية.

نستخدم عادةً خدمات شركات الشحن الدولية مثل DHL وFedEx وUPS وغيرها. ويمكن اختيار شركة الشحن وفقًا للوجهة وسرعة التسليم وحجم الشحنة ومتطلبات العميل.

تخضع منتجاتنا عمومًا لضمان لمدة 12 شهرًا. كما يمكن إرجاع المنتجات المؤهلة بموجب سياسة استرداد الأموال خلال 30 يومًا. يُرجى التواصل مع فريقنا قبل إرجاع أي منتج لتأكيد الشروط المعمول بها وتعليمات الإرجاع.

Products FAQs

قد يعجبك أيضًا