
Obavijest e-poštom kada ovaj proizvod postane dostupan
- Opis
- Reviews
- Dostava i plaćanje
Configured for point-to-point analog signal routing in Modicon X80 and Modicon M340 I/O architectures, the Schneider Electric BMXFTA152 (BMXFTA152 Preformed Cord Set) provides direct physical and electrical execution between a 20-pin removable terminal block and a 25-pin SUB-D connector. This 1.5 m cable assembly links the BMXAMO0802 8-channel analog output module directly to the ABE7CPA02 Advantys Telefast sub-base without manual wire-by-wire termination.
Suffix Breakdown & Model Matrix
The BMXFTA152 designation follows the Schneider Electric Modicon X80 cabling nomenclature:
- BMX: Modicon X80 I/O platform hardware prefix.
- FTA: Preformed cord set series designed for Modicon X80 to Advantys Telefast ABE7 connection.
- 15: Cable length indicator specifying a 1.5 m assembly.
- 2: Connector configuration code denoting a 20-pin removable terminal block (module side) to a 25-pin SUB-D connector (sub-base side).
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | BMXFTA152 |
| Brand | Schneider Electric |
| Origin | Not specified in source documentation |
| Weight | 0.32 kg |
| Dimensions | 1.5 m length (packaged: 4.0 cm H x 21.0 cm W x 21.0 cm L) |
| Operating Temp | Not specified in source documentation |
| Power Consumption | 0 W (passive interconnect assembly) |
| Series | Modicon X80 |
| Module Side Connector | 1 x 20-pin removable terminal block |
| Sub-Base Side Connector | 1 x 25-pin SUB-D male connector |
| Compatible I/O Module | BMXAMO0802 (Modicon M340 / X80 Analog Output) |
| Compatible Sub-Base | ABE7CPA02 (Advantys Telefast) |
| EAN Code | 3595864080468 |
I/O Density Scaling & Backplane Bus Integration
In high-density Modicon X80 racks, direct field wiring to 20-pin module headers creates mechanical strain and increases termination errors during commissioning. The BMXFTA152 offloads field wiring from the chassis front plane to a DIN-rail mounted ABE7CPA02 Telefast sub-base. By consolidating 8 analog output channels into a single shielded multi-conductor trunk, the assembly preserves backplane bus slot density while isolating field terminal torque stresses from the BMXAMO0802 module printed circuit board.
Frequently Asked Questions
Q: Can the BMXFTA152 be disconnected from the BMXAMO0802 module while the Modicon X80 rack is powered?A: While the Modicon X80 architecture supports module hot-swapping under specific controller configurations, unplugging the 20-pin removable terminal block under load interrupts all active 4-20 mA or 0-10 VDC analog output loops simultaneously, forcing connected actuators to their zero-energy state.
Q: Does this cable draw current from the Modicon X80 backplane bus?A: No. The BMXFTA152 is a strictly passive copper interconnect. All backplane current draw originates solely from the host BMXAMO0802 analog output module.
Q: Is the BMXFTA152 pin-compatible with 28-pin or 40-pin Modicon X80 digital I/O modules?A: No. The module-side connector is mechanically keyed and wired exclusively for 20-pin terminal block headers, specifically matched to the channel pinout of the BMXAMO0802 and ABE7CPA02 combination.
Field Installation Guidelines
- Power Isolation: De-energize external 24 VDC loop power supplies feeding the ABE7CPA02 sub-base before mating connectors.
- Module-Side Seating: Align the 20-pin removable terminal block with the front header of the BMXAMO0802 module. Press firmly until the top and bottom locking latches engage, then tighten the captive retention screws.
- Sub-Base Connection: Mate the 25-pin SUB-D connector to the corresponding port on the ABE7CPA02 Telefast sub-base and secure both thumbscrews to prevent vibration-induced loosening.
- Cable Routing & Bend Radius: Route the 1.5 m cable through dedicated analog signal ducts, maintaining at least 200 mm separation from AC power lines and variable frequency drive (VFD) motor leads to prevent electromagnetic interference. Avoid sharp bends within 50 mm of either connector strain relief.
Plaćanje: T/T, Western Union.
Luka otpreme: Xiamen.
Rok isporuke: Obično 1–3 radna dana nakon potvrde plaćanja (ovisno o zalihi).
Isporuka diljem svijeta: Industrijske dijelove za automatizaciju šaljemo kupcima diljem svijeta. Trošak prijevoza navodi se u vašem zahtjevu za ponudu.
Često postavljana pitanja
Česta pitanja o ponudama, dostavi, jamstvu i povratimaNa stranici proizvoda kliknite Zatražite ponudu i pošaljite nam broj dijela, potrebnu količinu i odredišnu zemlju. Naš prodajni tim odgovorit će vam s informacijama o trenutačnoj dostupnosti, cijeni i procijenjenom roku isporuke.
Artikli koji su na zalihi obično se pripremaju nakon plaćanja i potvrde narudžbe. Većina narudžbi šalje se iz našeg skladišta u Kini, iako se mjesto slanja može razlikovati ovisno o trenutačnim zalihama.
Da. Šaljemo dijelove za industrijsku automatizaciju kupcima diljem svijeta. Troškovi dostave i vrijeme isporuke ovise o odredištu, težini paketa, veličini proizvoda i lokalnim uvoznim zahtjevima.
Najčešće upotrebljavamo DHL, FedEx, UPS i druge međunarodne kurirske službe. Prijevoznik se može odabrati prema odredištu, brzini dostave, veličini pošiljke i zahtjevima kupca.
Naši su proizvodi općenito pokriveni 12-mjesečnim jamstvom. Proizvodi koji ispunjavaju uvjete mogu se također vratiti u skladu s našom 30-dnevnom politikom povrata novca. Obratite se našem timu prije vraćanja bilo kojeg artikla kako biste potvrdili primjenjive uvjete i upute za povrat.
Možda će vam se također svidjeti
Objave na blogu
Vijesti o industrijskoj automatizaciji, tehnički vodiči i novosti o proizvodima.
