Vai alle informazioni sul prodotto
1 di 3

Schneider Electric BMXFTB2800 Modicon X80 28-Pin Removable Terminal Block

18 disponibili
  • Manufacturer: Schneider
  • Product No.: BMXFTB2800
  • Country of origin: France
  • Product Type: Modicon X80 28-Pin Removable Terminal Block
  • Condition: Completamente nuovo
  • Payment: Bonifico telegrafico, Western Union
  • Weight: 0.111 kg
  • Shipping port: Xiamen
  • Warranty: 12 mesi
  • Descrizione
  • Reviews
  • Spedizione e pagamento

The Schneider Electric BMXFTB2800, also identified as the BMXFTB2800 removable terminal block, provides a 28-pin electrical connection interface for compatible Modicon X80 I/O modules. It uses removable screw-clamp terminals to connect field wiring to the module. The terminal block accepts conductors with cross-sections from 0.34 mm2 to 1 mm2 and is designed for modules equipped with a 28-pin removable terminal strip.

Hardware Specifications

Parameter Specification
Model BMXFTB2800
Brand Schneider Electric
Product Series Modicon X80
Product Type 28-Pin Removable Terminal Block
Accessory Type Removable Connection Block
Terminal Configuration 28 removable terminals
Connection Type Screw-clamp terminal
Conductor Cross-Section 0.34-1 mm2
Compatible Platform Modicon M580 / M340 PAC
Intended Application Modules with 28-pin removable terminal strips
Product Weight 0.111 kg
Power Consumption Passive connection accessory; no consumption value specified
EAN 3595864133621
Environmental Carbon Footprint 10 kg CO2 eq.

Modicon X80 Terminal Connection and Wiring Characteristics

The BMXFTB2800 provides a detachable field-wiring interface for compatible Modicon X80 modules. Its 28-pin configuration allows the module-side electrical connections to be disconnected together with the removable terminal block during maintenance or module replacement.

The screw-clamp connection design secures individual conductors mechanically. Supported conductor cross-sections range from 0.34 mm2 to 1 mm2.

For installation, conductor preparation and tightening must follow the manufacturer's terminal connection instructions. Verify the terminal assignment against the corresponding I/O module wiring diagram before reconnecting field signals.

The Modicon X80 platform supports common module hardware across M580 and M340 PAC architectures. However, compatibility of the BMXFTB2800 must be confirmed against the specific module's terminal-block requirements.

Frequently Asked Questions (FAQ)

Q: Which Modicon X80 modules can use the BMXFTB2800?

A: It is intended for modules equipped with a 28-pin removable terminal strip. Confirm the exact module reference and terminal configuration before installation.

Q: What conductor sizes are supported by the BMXFTB2800?

A: The specified conductor cross-section is 0.34 mm2 to 1 mm2. Actual conductor preparation must comply with the module and terminal connection instructions.

Q: Can the BMXFTB2800 be disconnected during module maintenance?

A: The terminal block is designed to be removable. Before disconnecting it, isolate the relevant field circuits and follow the controller manufacturer's maintenance procedures. Its removability does not establish that the connected module supports hot-swapping under energized conditions.

Field Installation Guidelines

  1. Module Verification: Confirm that the target Modicon X80 module uses a compatible 28-pin removable terminal block.
  2. Power Isolation: Isolate relevant field power and signal circuits before wiring or removing the terminal block.
  3. Conductor Preparation: Select conductors within the specified 0.34-1 mm2 cross-section range.
  4. Terminal Assignment: Match each conductor to the module's official terminal allocation diagram.
  5. Mechanical Connection: Secure conductors using the specified screw-clamp procedure and manufacturer tightening requirements.
  6. Cable Routing: Separate low-level analog signal wiring from high-voltage and high-current conductors where applicable.
  7. Grounding and Shielding: Terminate cable shields according to the system grounding design and the connected module's installation instructions.
  8. Final Inspection: Check conductor retention, terminal alignment, wiring identification, and correct seating of the removable block before restoring power.

Pagamento: T/T, Western Union.

Porto di spedizione: Xiamen.

Tempi di consegna: In genere 1–3 giorni lavorativi dopo la conferma del pagamento (in base alla disponibilità).

Consegna in tutto il mondo: Spediamo componenti per l’automazione industriale a clienti di tutto il mondo. Il costo del trasporto viene indicato nel preventivo relativo alla vostra richiesta.

Domande frequenti (FAQ)

Domande frequenti su preventivi, spedizione, garanzia e resi

Fai clic su Richiedi un preventivo nella pagina del prodotto e inviaci il codice prodotto, la quantità richiesta e il Paese di destinazione. Il nostro team commerciale ti risponderà indicando la disponibilità attuale, il prezzo e i tempi di consegna stimati.

Gli articoli disponibili vengono normalmente preparati dopo il pagamento e la conferma dell’ordine. La maggior parte degli ordini viene spedita dal nostro magazzino in Cina, anche se il luogo di spedizione può variare in base alle scorte disponibili.

Sì. Spediamo componenti per l’automazione industriale a clienti in tutto il mondo. Il costo e i tempi di spedizione dipendono dalla destinazione, dal peso del pacco, dalle dimensioni del prodotto e dai requisiti locali per l’importazione.

Utilizziamo comunemente i servizi di corriere internazionali DHL, FedEx, UPS e altri. Il corriere può essere scelto in base alla destinazione, alla velocità di consegna, alle dimensioni della spedizione e alle esigenze del cliente.

I nostri prodotti sono generalmente coperti da una garanzia di 12 mesi. I prodotti idonei possono inoltre essere restituiti ai sensi della nostra politica di rimborso entro 30 giorni. Contatta il nostro team prima di restituire qualsiasi articolo per confermare i termini applicabili e le istruzioni per la restituzione.

Products FAQs

Potrebbe piacerti anche