
แจ้งเตือนทางอีเมลเมื่อสินค้านี้พร้อมจำหน่าย
- คำอธิบาย
- Reviews
- การจัดส่งและการชำระเงิน
The Schneider Electric BMXCRA31200, also cataloged as the BMXCRA31200 Ethernet Remote I/O (RIO) Head Adapter, provides EtherNet/IP communication between a Modicon M580 or compatible automation controller and distributed Modicon X80 I/O modules. It collects input data from remote modules and distributes output data received from the controller through a two-port Ethernet RIO network.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | BMXCRA31200 |
| Brand | Schneider Electric |
| Series | Modicon X80 |
| Product Type | Ethernet Remote I/O Head Adapter |
| Weight | 0.225 kg |
| Dimensions | 32 x 100 x 87.5 mm (W x H x D) |
| Operating Temp | 0 to 60 deg C |
| Storage Temperature | -40 to 85 deg C |
| Power Consumption | 1200 mA current consumption |
| Input Voltage | 3.3 VDC |
| Bus Type | X-Bus via remote module rack |
| Ethernet Ports | 2 x RJ45 |
| Communication Protocol | EtherNet/IP |
| Network Type | IPv4 |
| Ethernet Speed | 10/100 Mbit/s |
| Ethernet Interface | 10/100BASE-TX |
| Network Redundancy | RSTP ring topology support |
| Communication Modes | Half-duplex, Full-duplex, Auto-Negotiation, Auto-MDIX |
| Compatible Controllers | Modicon M580, Modicon Quantum |
| Digital I/O Capacity | 0 to 128 channels |
| Analog I/O Capacity | 0 to 16 channels |
| Diagnostic Services | Modbus TCP Server, SNMP Agent, SNTP Client, DHCP Client, TFTP Client, FTP Client, FDR Client |
| Additional Services | QoS, CIP Explicit Messaging, Syslog |
| Configuration Function | CCOTF (Configuration Change on the Fly) |
| Event Timestamping | 10 ms |
| Protection Rating | IP20 |
| Installation | Rack-mounted, secured with two screws |
| Maximum Operating Altitude | 2000 m |
| Maximum Transport Altitude | 3000 m |
| Relative Humidity | 95%, non-condensing |
| Certifications | CE, UL, CSA, RCM, EAC, Merchant Navy |
| Standards | IEC 61131-2, IEC 61010-2-201, IEC 61850-3, IEC 61000-6-5 |
| EAN | 3595864132457 |
EtherNet/IP Communication and Remote I/O Architecture
The BMXCRA31200 operates as the communication head of a Modicon X80 Ethernet Remote I/O drop. Its two RJ45 interfaces connect the remote rack to the Ethernet RIO network using EtherNet/IP.
The data exchange follows two directions:
- Input processing: Remote digital and analog input modules acquire field signals and transfer the collected data through the X-Bus to the head adapter. The adapter communicates this information to the controller over the Ethernet RIO network.
- Output processing: The adapter receives output data from the controller and distributes it to the corresponding remote output modules through the X-Bus.
RSTP support enables ring network topology. The adapter also provides network diagnostics, device diagnostics through Device DDT, and a 10 ms timestamping function for event data.
CCOTF allows supported configuration changes without stopping the PLC. Actual availability depends on the controller architecture, configuration and supported module functions.
Frequently Asked Questions
Q: Does the BMXCRA31200 support hot-swapping?
A: The supplied documentation specifies rack installation and fastening with two screws but does not establish hot-swap capability. Replacement procedures should follow the Modicon X80 hardware and system maintenance instructions.
Q: What is the current consumption and backplane voltage of this adapter?
A: The specified current consumption is 1200 mA, with an input voltage of 3.3 VDC. The rack power budget should account for this load together with the installed I/O modules.
Q: Can the BMXCRA31200 operate in an Ethernet ring network?
A: Yes. It supports RSTP ring topology through its two Ethernet ports. Network configuration and recovery behavior must be coordinated with the connected Ethernet RIO devices and controller architecture.
Field Installation Guidelines
- Rack Installation: Install the BMXCRA31200 in the designated Modicon X80 module rack and secure it using the specified two mounting screws.
- Power Verification: Check the rack power supply and verify that the specified 3.3 VDC input and 1200 mA current requirement are accommodated by the system power budget.
- Ethernet Connections: Connect the two RJ45 interfaces to the designated Ethernet RIO network ports. Verify cable integrity, connector engagement and network topology before commissioning.
- Network Configuration: Configure the adapter within the controller's Ethernet RIO architecture. Check IP addressing, EtherNet/IP communication and RSTP settings.
- Grounding and Shielding: Follow Schneider Electric grounding instructions for the X80 rack and Ethernet installation. Maintain appropriate separation between communication cables and high-voltage or motor power wiring.
- LED Diagnostics: Inspect the RUN, ERR, Mod Status, Net Status and STS indicators. Confirm normal module operation and Ethernet communication before enabling field output operations.
- Environmental Conditions: Maintain an operating temperature between 0 and 60 deg C. The enclosure must provide protection appropriate to the module's IP20 rating.
- Configuration Validation: Verify I/O channel allocation, Device DDT diagnostics and controller communication after installation. Test input acquisition and output updates before returning the remote station to service.
การชำระเงิน: T/T, Western Union
ท่าเรือขนส่ง: เซี่ยเหมิน
ระยะเวลาดำเนินการ: โดยทั่วไป 1–3 วันทำการหลังยืนยันการชำระเงิน (ขึ้นอยู่กับสินค้าในสต็อก)
จัดส่งทั่วโลก: เราจัดส่งชิ้นส่วนระบบอัตโนมัติทางอุตสาหกรรมให้แก่ลูกค้าทั่วโลก โดยจะแจ้งค่าขนส่งพร้อมใบขอใบเสนอราคาของคุณ
คำถามที่พบบ่อย
คำถามที่พบบ่อยเกี่ยวกับใบเสนอราคา การจัดส่ง การรับประกัน และการคืนสินค้าคลิก ขอใบเสนอราคา ในหน้าสินค้า แล้วส่งหมายเลขชิ้นส่วน จำนวนที่ต้องการ และประเทศปลายทางให้เรา ทีมฝ่ายขายของเราจะตอบกลับพร้อมข้อมูลสินค้าที่มีจำหน่าย ราคา และระยะเวลาจัดส่งโดยประมาณ
สินค้าที่มีอยู่ในสต็อกโดยปกติจะจัดเตรียมหลังจากได้รับการชำระเงินและยืนยันคำสั่งซื้อแล้ว คำสั่งซื้อส่วนใหญ่จัดส่งจากคลังสินค้าของเราในประเทศจีน แต่สถานที่จัดส่งอาจแตกต่างกันไปตามสต็อกปัจจุบัน
ใช่ เราจัดส่งชิ้นส่วนระบบอัตโนมัติทางอุตสาหกรรมให้ลูกค้าทั่วโลก ค่าจัดส่งและระยะเวลาในการขนส่งขึ้นอยู่กับปลายทาง น้ำหนักพัสดุ ขนาดสินค้า และข้อกำหนดการนำเข้าของท้องถิ่น
เราใช้บริการ DHL, FedEx, UPS และบริษัทขนส่งระหว่างประเทศอื่น ๆ เป็นประจำ โดยสามารถเลือกผู้ให้บริการขนส่งได้ตามปลายทาง ความเร็วในการจัดส่ง ขนาดของพัสดุ และความต้องการของลูกค้า
โดยทั่วไป สินค้าของเราครอบคลุมการรับประกัน 12 เดือน สินค้าที่มีสิทธิ์ยังสามารถส่งคืนได้ภายใต้นโยบายคืนเงินภายใน 30 วัน โปรดติดต่อทีมงานของเราก่อนส่งคืนสินค้าใด ๆ เพื่อยืนยันข้อกำหนดที่ใช้บังคับและคำแนะนำในการส่งคืน
คุณอาจชอบสิ่งเหล่านี้ด้วย
บทความในบล็อก
ข่าวสารระบบอัตโนมัติในภาคอุตสาหกรรม คู่มือด้านเทคนิค และอัปเดตผลิตภัณฑ์
