ข้ามไปยังข้อมูลผลิตภัณฑ์
1 ของ 3

Schneider Electric BMXFTB2800 Modicon X80 28-Pin Removable Terminal Block

มีสินค้า 18 ชิ้น ทดลองใช้ฟรี
  • Manufacturer: Schneider
  • Product No.: BMXFTB2800
  • Country of origin: France
  • Product Type: Modicon X80 28-Pin Removable Terminal Block
  • Condition: ใหม่เอี่ยม
  • Payment: T/T, เวสเทิร์น ยูเนียน
  • Weight: 0.111 kg
  • Shipping port: เซี่ยเหมิน
  • Warranty: 12 เดือน
  • คำอธิบาย
  • Reviews
  • การจัดส่งและการชำระเงิน

The Schneider Electric BMXFTB2800, also identified as the BMXFTB2800 removable terminal block, provides a 28-pin electrical connection interface for compatible Modicon X80 I/O modules. It uses removable screw-clamp terminals to connect field wiring to the module. The terminal block accepts conductors with cross-sections from 0.34 mm2 to 1 mm2 and is designed for modules equipped with a 28-pin removable terminal strip.

Hardware Specifications

Parameter Specification
Model BMXFTB2800
Brand Schneider Electric
Product Series Modicon X80
Product Type 28-Pin Removable Terminal Block
Accessory Type Removable Connection Block
Terminal Configuration 28 removable terminals
Connection Type Screw-clamp terminal
Conductor Cross-Section 0.34-1 mm2
Compatible Platform Modicon M580 / M340 PAC
Intended Application Modules with 28-pin removable terminal strips
Product Weight 0.111 kg
Power Consumption Passive connection accessory; no consumption value specified
EAN 3595864133621
Environmental Carbon Footprint 10 kg CO2 eq.

Modicon X80 Terminal Connection and Wiring Characteristics

The BMXFTB2800 provides a detachable field-wiring interface for compatible Modicon X80 modules. Its 28-pin configuration allows the module-side electrical connections to be disconnected together with the removable terminal block during maintenance or module replacement.

The screw-clamp connection design secures individual conductors mechanically. Supported conductor cross-sections range from 0.34 mm2 to 1 mm2.

For installation, conductor preparation and tightening must follow the manufacturer's terminal connection instructions. Verify the terminal assignment against the corresponding I/O module wiring diagram before reconnecting field signals.

The Modicon X80 platform supports common module hardware across M580 and M340 PAC architectures. However, compatibility of the BMXFTB2800 must be confirmed against the specific module's terminal-block requirements.

Frequently Asked Questions (FAQ)

Q: Which Modicon X80 modules can use the BMXFTB2800?

A: It is intended for modules equipped with a 28-pin removable terminal strip. Confirm the exact module reference and terminal configuration before installation.

Q: What conductor sizes are supported by the BMXFTB2800?

A: The specified conductor cross-section is 0.34 mm2 to 1 mm2. Actual conductor preparation must comply with the module and terminal connection instructions.

Q: Can the BMXFTB2800 be disconnected during module maintenance?

A: The terminal block is designed to be removable. Before disconnecting it, isolate the relevant field circuits and follow the controller manufacturer's maintenance procedures. Its removability does not establish that the connected module supports hot-swapping under energized conditions.

Field Installation Guidelines

  1. Module Verification: Confirm that the target Modicon X80 module uses a compatible 28-pin removable terminal block.
  2. Power Isolation: Isolate relevant field power and signal circuits before wiring or removing the terminal block.
  3. Conductor Preparation: Select conductors within the specified 0.34-1 mm2 cross-section range.
  4. Terminal Assignment: Match each conductor to the module's official terminal allocation diagram.
  5. Mechanical Connection: Secure conductors using the specified screw-clamp procedure and manufacturer tightening requirements.
  6. Cable Routing: Separate low-level analog signal wiring from high-voltage and high-current conductors where applicable.
  7. Grounding and Shielding: Terminate cable shields according to the system grounding design and the connected module's installation instructions.
  8. Final Inspection: Check conductor retention, terminal alignment, wiring identification, and correct seating of the removable block before restoring power.

การชำระเงิน: T/T, Western Union

ท่าเรือขนส่ง: เซี่ยเหมิน

ระยะเวลาดำเนินการ: โดยทั่วไป 1–3 วันทำการหลังยืนยันการชำระเงิน (ขึ้นอยู่กับสินค้าในสต็อก)

จัดส่งทั่วโลก: เราจัดส่งชิ้นส่วนระบบอัตโนมัติทางอุตสาหกรรมให้แก่ลูกค้าทั่วโลก โดยจะแจ้งค่าขนส่งพร้อมใบขอใบเสนอราคาของคุณ

คำถามที่พบบ่อย

คำถามที่พบบ่อยเกี่ยวกับใบเสนอราคา การจัดส่ง การรับประกัน และการคืนสินค้า

คลิก ขอใบเสนอราคา ในหน้าสินค้า แล้วส่งหมายเลขชิ้นส่วน จำนวนที่ต้องการ และประเทศปลายทางให้เรา ทีมฝ่ายขายของเราจะตอบกลับพร้อมข้อมูลสินค้าที่มีจำหน่าย ราคา และระยะเวลาจัดส่งโดยประมาณ

สินค้าที่มีอยู่ในสต็อกโดยปกติจะจัดเตรียมหลังจากได้รับการชำระเงินและยืนยันคำสั่งซื้อแล้ว คำสั่งซื้อส่วนใหญ่จัดส่งจากคลังสินค้าของเราในประเทศจีน แต่สถานที่จัดส่งอาจแตกต่างกันไปตามสต็อกปัจจุบัน

ใช่ เราจัดส่งชิ้นส่วนระบบอัตโนมัติทางอุตสาหกรรมให้ลูกค้าทั่วโลก ค่าจัดส่งและระยะเวลาในการขนส่งขึ้นอยู่กับปลายทาง น้ำหนักพัสดุ ขนาดสินค้า และข้อกำหนดการนำเข้าของท้องถิ่น

เราใช้บริการ DHL, FedEx, UPS และบริษัทขนส่งระหว่างประเทศอื่น ๆ เป็นประจำ โดยสามารถเลือกผู้ให้บริการขนส่งได้ตามปลายทาง ความเร็วในการจัดส่ง ขนาดของพัสดุ และความต้องการของลูกค้า

โดยทั่วไป สินค้าของเราครอบคลุมการรับประกัน 12 เดือน สินค้าที่มีสิทธิ์ยังสามารถส่งคืนได้ภายใต้นโยบายคืนเงินภายใน 30 วัน โปรดติดต่อทีมงานของเราก่อนส่งคืนสินค้าใด ๆ เพื่อยืนยันข้อกำหนดที่ใช้บังคับและคำแนะนำในการส่งคืน

Products FAQs

คุณอาจชอบสิ่งเหล่านี้ด้วย