
Bu ürün stokta olduğunda e-posta ile bilgilendirileceksiniz
- Açıklama
- Reviews
- Kargo ve Ödeme
The Schneider Electric BMXCRA31200, also cataloged as the BMXCRA31200 Ethernet Remote I/O (RIO) Head Adapter, provides EtherNet/IP communication between a Modicon M580 or compatible automation controller and distributed Modicon X80 I/O modules. It collects input data from remote modules and distributes output data received from the controller through a two-port Ethernet RIO network.
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | BMXCRA31200 |
| Brand | Schneider Electric |
| Series | Modicon X80 |
| Product Type | Ethernet Remote I/O Head Adapter |
| Weight | 0.225 kg |
| Dimensions | 32 x 100 x 87.5 mm (W x H x D) |
| Operating Temp | 0 to 60 deg C |
| Storage Temperature | -40 to 85 deg C |
| Power Consumption | 1200 mA current consumption |
| Input Voltage | 3.3 VDC |
| Bus Type | X-Bus via remote module rack |
| Ethernet Ports | 2 x RJ45 |
| Communication Protocol | EtherNet/IP |
| Network Type | IPv4 |
| Ethernet Speed | 10/100 Mbit/s |
| Ethernet Interface | 10/100BASE-TX |
| Network Redundancy | RSTP ring topology support |
| Communication Modes | Half-duplex, Full-duplex, Auto-Negotiation, Auto-MDIX |
| Compatible Controllers | Modicon M580, Modicon Quantum |
| Digital I/O Capacity | 0 to 128 channels |
| Analog I/O Capacity | 0 to 16 channels |
| Diagnostic Services | Modbus TCP Server, SNMP Agent, SNTP Client, DHCP Client, TFTP Client, FTP Client, FDR Client |
| Additional Services | QoS, CIP Explicit Messaging, Syslog |
| Configuration Function | CCOTF (Configuration Change on the Fly) |
| Event Timestamping | 10 ms |
| Protection Rating | IP20 |
| Installation | Rack-mounted, secured with two screws |
| Maximum Operating Altitude | 2000 m |
| Maximum Transport Altitude | 3000 m |
| Relative Humidity | 95%, non-condensing |
| Certifications | CE, UL, CSA, RCM, EAC, Merchant Navy |
| Standards | IEC 61131-2, IEC 61010-2-201, IEC 61850-3, IEC 61000-6-5 |
| EAN | 3595864132457 |
EtherNet/IP Communication and Remote I/O Architecture
The BMXCRA31200 operates as the communication head of a Modicon X80 Ethernet Remote I/O drop. Its two RJ45 interfaces connect the remote rack to the Ethernet RIO network using EtherNet/IP.
The data exchange follows two directions:
- Input processing: Remote digital and analog input modules acquire field signals and transfer the collected data through the X-Bus to the head adapter. The adapter communicates this information to the controller over the Ethernet RIO network.
- Output processing: The adapter receives output data from the controller and distributes it to the corresponding remote output modules through the X-Bus.
RSTP support enables ring network topology. The adapter also provides network diagnostics, device diagnostics through Device DDT, and a 10 ms timestamping function for event data.
CCOTF allows supported configuration changes without stopping the PLC. Actual availability depends on the controller architecture, configuration and supported module functions.
Frequently Asked Questions
Q: Does the BMXCRA31200 support hot-swapping?
A: The supplied documentation specifies rack installation and fastening with two screws but does not establish hot-swap capability. Replacement procedures should follow the Modicon X80 hardware and system maintenance instructions.
Q: What is the current consumption and backplane voltage of this adapter?
A: The specified current consumption is 1200 mA, with an input voltage of 3.3 VDC. The rack power budget should account for this load together with the installed I/O modules.
Q: Can the BMXCRA31200 operate in an Ethernet ring network?
A: Yes. It supports RSTP ring topology through its two Ethernet ports. Network configuration and recovery behavior must be coordinated with the connected Ethernet RIO devices and controller architecture.
Field Installation Guidelines
- Rack Installation: Install the BMXCRA31200 in the designated Modicon X80 module rack and secure it using the specified two mounting screws.
- Power Verification: Check the rack power supply and verify that the specified 3.3 VDC input and 1200 mA current requirement are accommodated by the system power budget.
- Ethernet Connections: Connect the two RJ45 interfaces to the designated Ethernet RIO network ports. Verify cable integrity, connector engagement and network topology before commissioning.
- Network Configuration: Configure the adapter within the controller's Ethernet RIO architecture. Check IP addressing, EtherNet/IP communication and RSTP settings.
- Grounding and Shielding: Follow Schneider Electric grounding instructions for the X80 rack and Ethernet installation. Maintain appropriate separation between communication cables and high-voltage or motor power wiring.
- LED Diagnostics: Inspect the RUN, ERR, Mod Status, Net Status and STS indicators. Confirm normal module operation and Ethernet communication before enabling field output operations.
- Environmental Conditions: Maintain an operating temperature between 0 and 60 deg C. The enclosure must provide protection appropriate to the module's IP20 rating.
- Configuration Validation: Verify I/O channel allocation, Device DDT diagnostics and controller communication after installation. Test input acquisition and output updates before returning the remote station to service.
Ödeme: T/T, Western Union.
Sevkiyat limanı: Xiamen.
Teslim süresi: Ödeme onayından sonra genellikle 1–3 iş günü (stok durumuna bağlıdır).
Dünya genelinde teslimat: Endüstriyel otomasyon parçalarını dünyanın dört bir yanındaki müşterilerimize gönderiyoruz. Nakliye ücreti, RFQ’nuzla birlikte teklif edilir.
Sıkça Sorulan Sorular
Teklifler, gönderim, garanti ve iadeler hakkında sık sorulan sorularÜrün sayfasında Teklif İste seçeneğine tıklayın ve parça numarasını, gereken miktarı ve varış ülkesini bize gönderin. Satış ekibimiz güncel stok durumu, fiyatlandırma ve tahmini teslimat süresiyle size yanıt verecektir.
Stokta bulunan ürünler normalde ödeme ve sipariş onayından sonra hazırlanır. Çoğu sipariş Çin'deki depomuzdan gönderilir; ancak gönderim konumu mevcut stoğa bağlı olarak değişebilir.
Evet. Endüstriyel otomasyon parçalarını dünya genelindeki müşterilere gönderiyoruz. Kargo ücreti ve taşıma süresi; varış noktasına, paketin ağırlığına, ürünün boyutuna ve yerel ithalat gerekliliklerine bağlıdır.
Genellikle DHL, FedEx, UPS ve diğer uluslararası kurye hizmetlerini kullanıyoruz. Taşıyıcı; varış noktasına, teslimat hızına, gönderi boyutuna ve müşteri gereksinimlerine göre seçilebilir.
Ürünlerimiz genel olarak 12 aylık garanti kapsamındadır. Uygun ürünler ayrıca 30 günlük para iade politikamız kapsamında iade edilebilir. Uygulanabilir koşulları ve iade talimatlarını teyit etmek için lütfen herhangi bir ürünü iade etmeden önce ekibimizle iletişime geçin.
Bunlar da ilginizi çekebilir
Blog Gönderileri
Endüstriyel otomasyon haberleri, teknik kılavuzlar ve ürün güncellemeleri.
