
Đã thông báo qua email khi sản phẩm này có sẵn
- Mô tả
- Reviews
- Vận chuyển & Thanh toán
Configured for point-to-point analog signal routing in Modicon X80 and Modicon M340 I/O architectures, the Schneider Electric BMXFTA152 (BMXFTA152 Preformed Cord Set) provides direct physical and electrical execution between a 20-pin removable terminal block and a 25-pin SUB-D connector. This 1.5 m cable assembly links the BMXAMO0802 8-channel analog output module directly to the ABE7CPA02 Advantys Telefast sub-base without manual wire-by-wire termination.
Suffix Breakdown & Model Matrix
The BMXFTA152 designation follows the Schneider Electric Modicon X80 cabling nomenclature:
- BMX: Modicon X80 I/O platform hardware prefix.
- FTA: Preformed cord set series designed for Modicon X80 to Advantys Telefast ABE7 connection.
- 15: Cable length indicator specifying a 1.5 m assembly.
- 2: Connector configuration code denoting a 20-pin removable terminal block (module side) to a 25-pin SUB-D connector (sub-base side).
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | BMXFTA152 |
| Brand | Schneider Electric |
| Origin | Not specified in source documentation |
| Weight | 0.32 kg |
| Dimensions | 1.5 m length (packaged: 4.0 cm H x 21.0 cm W x 21.0 cm L) |
| Operating Temp | Not specified in source documentation |
| Power Consumption | 0 W (passive interconnect assembly) |
| Series | Modicon X80 |
| Module Side Connector | 1 x 20-pin removable terminal block |
| Sub-Base Side Connector | 1 x 25-pin SUB-D male connector |
| Compatible I/O Module | BMXAMO0802 (Modicon M340 / X80 Analog Output) |
| Compatible Sub-Base | ABE7CPA02 (Advantys Telefast) |
| EAN Code | 3595864080468 |
I/O Density Scaling & Backplane Bus Integration
In high-density Modicon X80 racks, direct field wiring to 20-pin module headers creates mechanical strain and increases termination errors during commissioning. The BMXFTA152 offloads field wiring from the chassis front plane to a DIN-rail mounted ABE7CPA02 Telefast sub-base. By consolidating 8 analog output channels into a single shielded multi-conductor trunk, the assembly preserves backplane bus slot density while isolating field terminal torque stresses from the BMXAMO0802 module printed circuit board.
Frequently Asked Questions
Q: Can the BMXFTA152 be disconnected from the BMXAMO0802 module while the Modicon X80 rack is powered?A: While the Modicon X80 architecture supports module hot-swapping under specific controller configurations, unplugging the 20-pin removable terminal block under load interrupts all active 4-20 mA or 0-10 VDC analog output loops simultaneously, forcing connected actuators to their zero-energy state.
Q: Does this cable draw current from the Modicon X80 backplane bus?A: No. The BMXFTA152 is a strictly passive copper interconnect. All backplane current draw originates solely from the host BMXAMO0802 analog output module.
Q: Is the BMXFTA152 pin-compatible with 28-pin or 40-pin Modicon X80 digital I/O modules?A: No. The module-side connector is mechanically keyed and wired exclusively for 20-pin terminal block headers, specifically matched to the channel pinout of the BMXAMO0802 and ABE7CPA02 combination.
Field Installation Guidelines
- Power Isolation: De-energize external 24 VDC loop power supplies feeding the ABE7CPA02 sub-base before mating connectors.
- Module-Side Seating: Align the 20-pin removable terminal block with the front header of the BMXAMO0802 module. Press firmly until the top and bottom locking latches engage, then tighten the captive retention screws.
- Sub-Base Connection: Mate the 25-pin SUB-D connector to the corresponding port on the ABE7CPA02 Telefast sub-base and secure both thumbscrews to prevent vibration-induced loosening.
- Cable Routing & Bend Radius: Route the 1.5 m cable through dedicated analog signal ducts, maintaining at least 200 mm separation from AC power lines and variable frequency drive (VFD) motor leads to prevent electromagnetic interference. Avoid sharp bends within 50 mm of either connector strain relief.
Thanh toán: T/T, Western Union.
Cảng vận chuyển: Hạ Môn.
Thời gian giao hàng: Thông thường từ 1–3 ngày làm việc sau khi xác nhận thanh toán (tùy tình trạng hàng tồn kho).
Giao hàng toàn cầu: Chúng tôi vận chuyển các linh kiện tự động hóa công nghiệp đến khách hàng trên toàn thế giới. Cước phí sẽ được báo cùng với yêu cầu báo giá của bạn.
Câu hỏi thường gặp
Các câu hỏi thường gặp về báo giá, vận chuyển, bảo hành và đổi trảNhấp vào Yêu cầu báo giá trên trang sản phẩm và gửi cho chúng tôi mã linh kiện, số lượng cần thiết và quốc gia nhận hàng. Đội ngũ bán hàng của chúng tôi sẽ phản hồi về tình trạng còn hàng, giá cả hiện tại và thời gian giao hàng dự kiến.
Các mặt hàng có sẵn thường được chuẩn bị sau khi thanh toán và xác nhận đơn hàng. Hầu hết đơn hàng được gửi đi từ kho của chúng tôi tại Trung Quốc, mặc dù địa điểm gửi hàng có thể thay đổi tùy theo tình trạng hàng tồn kho hiện tại.
Có. Chúng tôi vận chuyển linh kiện tự động hóa công nghiệp đến khách hàng trên toàn thế giới. Chi phí vận chuyển và thời gian giao hàng phụ thuộc vào điểm đến, trọng lượng kiện hàng, kích thước sản phẩm và các yêu cầu nhập khẩu tại địa phương.
Chúng tôi thường sử dụng DHL, FedEx, UPS và các dịch vụ chuyển phát quốc tế khác. Có thể lựa chọn đơn vị vận chuyển tùy theo điểm đến, tốc độ giao hàng, kích thước lô hàng và yêu cầu của khách hàng.
Các sản phẩm của chúng tôi thường được bảo hành 12 tháng. Các sản phẩm đủ điều kiện cũng có thể được trả lại theo chính sách hoàn tiền trong 30 ngày. Vui lòng liên hệ với đội ngũ của chúng tôi trước khi trả lại bất kỳ sản phẩm nào để xác nhận các điều khoản áp dụng và hướng dẫn trả hàng.
Bạn cũng có thể thích
Bài đăng blog
Tin tức về tự động hóa công nghiệp, hướng dẫn kỹ thuật và cập nhật sản phẩm.
