Zu den Produktinformationen springen
1 von 3

Schneider Electric BMXFTA152 Modicon X80 Preformed Cord Set

18 auf Lager
  • Manufacturer: Schneider
  • Product No.: BMXFTA152
  • Country of origin: France
  • Product Type: Modicon X80 Preformed Cord Set
  • Condition: Brandneu
  • Payment: T/T, Western Union
  • Weight: 0.32 kg
  • Shipping port: Xiamen
  • Warranty: 12 Monate
  • Beschreibung
  • Reviews
  • Versand & Zahlung

Configured for point-to-point analog signal routing in Modicon X80 and Modicon M340 I/O architectures, the Schneider Electric BMXFTA152 (BMXFTA152 Preformed Cord Set) provides direct physical and electrical execution between a 20-pin removable terminal block and a 25-pin SUB-D connector. This 1.5 m cable assembly links the BMXAMO0802 8-channel analog output module directly to the ABE7CPA02 Advantys Telefast sub-base without manual wire-by-wire termination.

Suffix Breakdown & Model Matrix

The BMXFTA152 designation follows the Schneider Electric Modicon X80 cabling nomenclature:

  • BMX: Modicon X80 I/O platform hardware prefix.
  • FTA: Preformed cord set series designed for Modicon X80 to Advantys Telefast ABE7 connection.
  • 15: Cable length indicator specifying a 1.5 m assembly.
  • 2: Connector configuration code denoting a 20-pin removable terminal block (module side) to a 25-pin SUB-D connector (sub-base side).

Hardware Specifications

Parameter Specification
Model BMXFTA152
Brand Schneider Electric
Origin Not specified in source documentation
Weight 0.32 kg
Dimensions 1.5 m length (packaged: 4.0 cm H x 21.0 cm W x 21.0 cm L)
Operating Temp Not specified in source documentation
Power Consumption 0 W (passive interconnect assembly)
Series Modicon X80
Module Side Connector 1 x 20-pin removable terminal block
Sub-Base Side Connector 1 x 25-pin SUB-D male connector
Compatible I/O Module BMXAMO0802 (Modicon M340 / X80 Analog Output)
Compatible Sub-Base ABE7CPA02 (Advantys Telefast)
EAN Code 3595864080468

I/O Density Scaling & Backplane Bus Integration

In high-density Modicon X80 racks, direct field wiring to 20-pin module headers creates mechanical strain and increases termination errors during commissioning. The BMXFTA152 offloads field wiring from the chassis front plane to a DIN-rail mounted ABE7CPA02 Telefast sub-base. By consolidating 8 analog output channels into a single shielded multi-conductor trunk, the assembly preserves backplane bus slot density while isolating field terminal torque stresses from the BMXAMO0802 module printed circuit board.

Frequently Asked Questions

Q: Can the BMXFTA152 be disconnected from the BMXAMO0802 module while the Modicon X80 rack is powered?A: While the Modicon X80 architecture supports module hot-swapping under specific controller configurations, unplugging the 20-pin removable terminal block under load interrupts all active 4-20 mA or 0-10 VDC analog output loops simultaneously, forcing connected actuators to their zero-energy state.

Q: Does this cable draw current from the Modicon X80 backplane bus?A: No. The BMXFTA152 is a strictly passive copper interconnect. All backplane current draw originates solely from the host BMXAMO0802 analog output module.

Q: Is the BMXFTA152 pin-compatible with 28-pin or 40-pin Modicon X80 digital I/O modules?A: No. The module-side connector is mechanically keyed and wired exclusively for 20-pin terminal block headers, specifically matched to the channel pinout of the BMXAMO0802 and ABE7CPA02 combination.

Field Installation Guidelines

  1. Power Isolation: De-energize external 24 VDC loop power supplies feeding the ABE7CPA02 sub-base before mating connectors.
  2. Module-Side Seating: Align the 20-pin removable terminal block with the front header of the BMXAMO0802 module. Press firmly until the top and bottom locking latches engage, then tighten the captive retention screws.
  3. Sub-Base Connection: Mate the 25-pin SUB-D connector to the corresponding port on the ABE7CPA02 Telefast sub-base and secure both thumbscrews to prevent vibration-induced loosening.
  4. Cable Routing & Bend Radius: Route the 1.5 m cable through dedicated analog signal ducts, maintaining at least 200 mm separation from AC power lines and variable frequency drive (VFD) motor leads to prevent electromagnetic interference. Avoid sharp bends within 50 mm of either connector strain relief.

Zahlung: T/T, Western Union.

Versandhafen: Xiamen.

Lieferzeit: In der Regel 1–3 Werktage nach Bestätigung der Zahlung (je nach Lagerbestand).

Weltweiter Versand: Wir versenden Teile für die industrielle Automatisierung an Kunden weltweit. Die Frachtkosten werden mit Ihrem RFQ angegeben.

Häufig gestellte Fragen

Häufige Fragen zu Angeboten, Versand, Garantie und Rückgaben

Klicken Sie auf der Produktseite auf Angebot anfordern und teilen Sie uns die Teilenummer, die benötigte Menge und das Zielland mit. Unser Vertriebsteam antwortet mit der aktuellen Verfügbarkeit, dem Preis und der voraussichtlichen Lieferzeit.

Vorrätige Artikel werden normalerweise nach Zahlung und Auftragsbestätigung vorbereitet. Die meisten Bestellungen werden von unserem Lager in China versandt, wobei der Versandort je nach aktuellem Lagerbestand variieren kann.

Ja. Wir versenden Teile für die industrielle Automatisierung an Kunden weltweit. Versandkosten und Lieferzeit hängen vom Bestimmungsort, dem Paketgewicht, der Produktgröße und den örtlichen Einfuhrbestimmungen ab.

Wir nutzen in der Regel DHL, FedEx, UPS und andere internationale Kurierdienste. Der Versanddienstleister kann je nach Zielort, Liefergeschwindigkeit, Sendungsgröße und Kundenanforderungen ausgewählt werden.

Unsere Produkte sind grundsätzlich durch eine 12-monatige Garantie abgedeckt. Für berechtigte Produkte ist außerdem eine Rückgabe gemäß unserer 30-Tage-Erstattungsrichtlinie möglich. Bitte kontaktieren Sie unser Team, bevor Sie einen Artikel zurücksenden, um die geltenden Bedingungen und Rücksendeanweisungen zu bestätigen.

Products FAQs

Das könnte Ihnen auch gefallen