
Bićete obavešteni imejlom kada ovaj proizvod bude dostupan
- Opis
- Reviews
- Dostava i plaćanje
Configured for point-to-point analog signal routing in Modicon X80 and Modicon M340 I/O architectures, the Schneider Electric BMXFTA152 (BMXFTA152 Preformed Cord Set) provides direct physical and electrical execution between a 20-pin removable terminal block and a 25-pin SUB-D connector. This 1.5 m cable assembly links the BMXAMO0802 8-channel analog output module directly to the ABE7CPA02 Advantys Telefast sub-base without manual wire-by-wire termination.
Suffix Breakdown & Model Matrix
The BMXFTA152 designation follows the Schneider Electric Modicon X80 cabling nomenclature:
- BMX: Modicon X80 I/O platform hardware prefix.
- FTA: Preformed cord set series designed for Modicon X80 to Advantys Telefast ABE7 connection.
- 15: Cable length indicator specifying a 1.5 m assembly.
- 2: Connector configuration code denoting a 20-pin removable terminal block (module side) to a 25-pin SUB-D connector (sub-base side).
Hardware Specifications
| Parameter | Specification |
|---|---|
| Model | BMXFTA152 |
| Brand | Schneider Electric |
| Origin | Not specified in source documentation |
| Weight | 0.32 kg |
| Dimensions | 1.5 m length (packaged: 4.0 cm H x 21.0 cm W x 21.0 cm L) |
| Operating Temp | Not specified in source documentation |
| Power Consumption | 0 W (passive interconnect assembly) |
| Series | Modicon X80 |
| Module Side Connector | 1 x 20-pin removable terminal block |
| Sub-Base Side Connector | 1 x 25-pin SUB-D male connector |
| Compatible I/O Module | BMXAMO0802 (Modicon M340 / X80 Analog Output) |
| Compatible Sub-Base | ABE7CPA02 (Advantys Telefast) |
| EAN Code | 3595864080468 |
I/O Density Scaling & Backplane Bus Integration
In high-density Modicon X80 racks, direct field wiring to 20-pin module headers creates mechanical strain and increases termination errors during commissioning. The BMXFTA152 offloads field wiring from the chassis front plane to a DIN-rail mounted ABE7CPA02 Telefast sub-base. By consolidating 8 analog output channels into a single shielded multi-conductor trunk, the assembly preserves backplane bus slot density while isolating field terminal torque stresses from the BMXAMO0802 module printed circuit board.
Frequently Asked Questions
Q: Can the BMXFTA152 be disconnected from the BMXAMO0802 module while the Modicon X80 rack is powered?A: While the Modicon X80 architecture supports module hot-swapping under specific controller configurations, unplugging the 20-pin removable terminal block under load interrupts all active 4-20 mA or 0-10 VDC analog output loops simultaneously, forcing connected actuators to their zero-energy state.
Q: Does this cable draw current from the Modicon X80 backplane bus?A: No. The BMXFTA152 is a strictly passive copper interconnect. All backplane current draw originates solely from the host BMXAMO0802 analog output module.
Q: Is the BMXFTA152 pin-compatible with 28-pin or 40-pin Modicon X80 digital I/O modules?A: No. The module-side connector is mechanically keyed and wired exclusively for 20-pin terminal block headers, specifically matched to the channel pinout of the BMXAMO0802 and ABE7CPA02 combination.
Field Installation Guidelines
- Power Isolation: De-energize external 24 VDC loop power supplies feeding the ABE7CPA02 sub-base before mating connectors.
- Module-Side Seating: Align the 20-pin removable terminal block with the front header of the BMXAMO0802 module. Press firmly until the top and bottom locking latches engage, then tighten the captive retention screws.
- Sub-Base Connection: Mate the 25-pin SUB-D connector to the corresponding port on the ABE7CPA02 Telefast sub-base and secure both thumbscrews to prevent vibration-induced loosening.
- Cable Routing & Bend Radius: Route the 1.5 m cable through dedicated analog signal ducts, maintaining at least 200 mm separation from AC power lines and variable frequency drive (VFD) motor leads to prevent electromagnetic interference. Avoid sharp bends within 50 mm of either connector strain relief.
Plaćanje: T/T, Western Union.
Luka otpreme: Siamen.
Rok isporuke: Obično 1–3 radna dana nakon potvrde uplate (u zavisnosti od zaliha).
Isporuka širom sveta: Šaljemo delove za industrijsku automatizaciju kupcima širom sveta. Troškovi prevoza se navode u vašem RFQ-u.
Česta pitanja (FAQ)
Najčešća pitanja o ponudama, isporuci, garanciji i povraćaju robeNa stranici proizvoda kliknite na Zatražite ponudu i pošaljite nam broj dela, potrebnu količinu i zemlju odredišta. Naš prodajni tim će odgovoriti informacijama o trenutnoj dostupnosti, ceni i procenjenom roku isporuke.
Artikli koji su na stanju obično se pripremaju nakon uplate i potvrde porudžbine. Većina porudžbina šalje se iz našeg skladišta u Kini, iako mesto slanja može da varira u zavisnosti od trenutnog stanja zaliha.
Da. Šaljemo delove za industrijsku automatizaciju kupcima širom sveta. Troškovi i vreme isporuke zavise od odredišta, težine paketa, veličine proizvoda i lokalnih uvoznih zahteva.
Najčešće koristimo DHL, FedEx, UPS i druge međunarodne kurirske službe. Prevoznik se može izabrati u skladu sa odredištem, brzinom isporuke, veličinom pošiljke i zahtevima kupca.
Naši proizvodi uglavnom imaju garanciju od 12 meseci. Proizvodi koji ispunjavaju uslove mogu se takođe vratiti u okviru naše politike povraćaja novca u roku od 30 dana. Obratite se našem timu pre vraćanja bilo kog artikla da biste potvrdili važeće uslove i uputstva za povraćaj.
Možda će vam se dopasti i
Blog objave
Vesti iz industrijske automatizacije, tehnički vodiči i novosti o proizvodima.
